Stacking and storage

DIY Metal Firewood Rack: Free Plans for a Welded Steel Rack

Free plans for a welded steel firewood rack that holds exactly a quarter cord (32 cubic feet). Cut list, materials and step-by-step build instructions, free PDF.

This welded steel firewood rack holds exactly a quarter cord (32 cubic feet) of 16-inch firewood. It's built from 1-1/2 inch square tube, sits on short legs off wet ground, and with a coat of paint will last for decades. It's a good first project for a new welder: all square cuts except four braces.

Download the free plans (PDF): drawing, cut list and steps on two printable pages.

Front and end view of the DIY welded steel firewood rack with dimensions

Why This Design

  • Exactly a quarter cord. 72 inches between the uprights, 48 inches under the top cross pieces and 16-inch wood is 32 cubic feet.
  • Full support for every split. The base is 16 inches wide, matching typical firewood length.
  • Braces outside the stack. The corner braces sit on the outside faces of the frame, so they never take up wood space.
  • Up on legs. Four-inch legs with foot plates keep the base rails out of standing water and away from rust.

Materials

  • About 42 ft of 1-1/2 in. square steel tube, 14 gauge (buy two 24 ft sticks)
  • 4 steel plates, 3 x 3 x 1/8 in., for feet
  • 4 plastic tube end caps, 1-1/2 in. (optional)
  • Degreaser, metal primer and exterior enamel, or a rust-preventive spray paint

Tools: MIG or flux-core welder, chop saw or angle grinder with cutoff wheels, magnetic square, clamps, and proper welding safety gear: helmet, gloves, long sleeves and eye protection for grinding.

Cut List

Part Qty Length Notes
Base rails 2 75 in. Square ends
Base cross pieces 3 13 in. Square ends
Uprights 4 49-1/2 in. Square ends
Top cross pieces 2 13 in. Square ends
Legs 4 4 in. Square ends
Corner braces 4 about 17 in. 45 degree ends, cut to fit

How to Build It

  1. Prep the steel. Cut every piece, grind the ends clean and wipe everything down with degreaser. Mill scale and oil make for bad welds and peeling paint.
  2. Weld the base. Lay the base rails on a flat surface and weld a 13 in. cross piece between them at each end and in the middle. The base is 16 in. wide outside. Measure the diagonals; they should match before you weld it solid.
  3. Weld the uprights. Stand an upright on top of each base corner, flush with the outside faces, and tack it. Check plumb in both directions with a level, then weld all the way around.
  4. Weld the top cross pieces between the tops of each end pair of uprights. That leaves 48 in. of stacking height above the base.
  5. Weld the corner braces. At each corner, set a brace flat against the outside faces of the upright and base rail, about 12 in. up and 12 in. in. Mark the 45 degree ends in place, cut and weld.
  6. Add legs and feet. Weld a 4 in. leg under each corner, just inside the end, and a 3 x 3 in. plate under each leg.
  7. Finish it. Grind off sharp edges and spatter, prime and paint. Cap the open tube ends to keep water and wasps out.

Stacking It

Stack 16-inch splits bark side up, one row deep, up to the top cross pieces. Full, it holds 32 cubic feet: a quarter cord. Build two for a half cord or four for a full cord.

Set it on level ground or pavers where it gets sun and wind, at least 20 feet from your house. Cover only the top, never the sides. More in our firewood storage guide.

Variations

  • No welder? Use bolt-together steel brackets with 2x4 rails, or build our 2x4 wood rack instead.
  • Longer rack. For an 8 ft or 12 ft rack, add a pair of uprights with a top cross piece in the middle so the base rails don't flex under the load.
  • Add a roof. Weld two pieces of 1 in. angle along the tops of the uprights and screw a corrugated roofing panel to them, overhanging a few inches on each side.

Rather Buy One?

Our guide to the best firewood racks covers what to look for in steel tube, covered and bracket-kit racks.

Once it's built, fill it with exactly a quarter cord of seasoned wood. Find firewood near you.

Now get the wood.

See if we deliver to your zip, or find a local provider in the free directory — 1244 listings and counting.